User's Guide About the product: VISIO Light is designed for the safety of dogs. The light tube can be adjusted to the circumference of the dog's neck (min. Length approx. 20 cm, max. Length approx. 70 cm). Note: The Visio Light is not a collar, but a position light ring! VISIO Light is also designed for cat safety. The buckle opens immediately when there is a risk of suffocation. The light tube can be adjusted to the perimeter of the cat's neck (min. Length approx. 20 cm, max. Length approx. 35 cm). Depending on the state of charge of the battery and the conditions of the site, the illuminated hoop can be seen from up to 500 m. Flashing or continuous lighting can be set on it (using the toggle switch). The device is drip-proof and high quality made of fabric. No battery required: instead, the device can be charged from a device with a USB port, such as a computer, using a standard USB cable. Accessories: 1 light neck ring 1 USB cable Safety: Before using the device, read and save the instructions below so that you can read them again later if necessary. If you give the device to someone, add the user guide as well. To get started with Visio Light: Before using Visio Light, read the instruction manual carefully and make sure that follow step by step instructions. Carefully remove Visio Light from its packaging to protect it from damage. Connect the included USB cable to the tube (using the small connector) and plug it into a USB port, for example, to a computer. The LED next to the Toggle Switch will turn off when the device is fully charged. Use only the USB cable provided with the device to charge Visio Light. The charging time is approx. 90 minutes to 2 hours. Fit Visio Light to your favorite neck. To do this, first measure the circumference of your pet’s neck. Place a tape measure around your pet's neck and measure its circumference so that the tape measure is not too tight and you have two fingers easily fit between the neck and the tape measure, this way you can ensure that the Visio Light fits perfectly. THE mark the appropriate size on the Visio Light and cut with a sharp scissors behind an LED: as shown in Figure 3. Replace the closing end on the beak: as shown in Figure 4. Visio Light is now ready for use. Using the toggle switch is different you can set lighting modes: 1. Continuous lighting 2. Fast flashing 3. Slow flashing Note: Visio Light can illuminate for approximately 90 minutes in continuous lighting mode and approximately 2 minutes in flashing mode hours before recharging. To clean Visio Light: The light tube can be wiped clean with a soft, dry cloth. Danger to children and certain people: The device should NOT be used as intended by children, people with reduced physical, sensory or mental capabilities or those who have no experience and / or knowledge of the use of the device, unless under the supervision of a person who constantly monitors and takes responsibility for their safety or when instructed to do so device. Children should be supervised to ensure that they do not play with the appliance. THE keep children away from their packaging. Risk of suffocation if swallowed. Product packaging is not can be pulled over the head. Risk of injury or damage to property: Protect from heat. Maximum ambient temperature -10 ° C / + 40 ° C Protect the product from physical injury due to impact or fall. Do not use any scratches or abrasives detergent, which may damage the surface of the product. Check the condition of the product before use. Do not use faulty device. Dangers of battery charging: Only use a charging station that is suitable for charging with lithium polymer batteries. Where the battery is not charged properly (too high voltage, too high temperature, electricity or bad charger), may cause overheating, explosion or fire. Do not charge the battery near a heat source or in a poorly insulated car. High temperatures can cause malfunctions in a battery, which may result in overheating, explosion, or fire. Due to the large amount of energy storage, a lithium polymer cells if damaged, heated, or exploded. This can happen due to extreme overcharging, overloading, dropping, mechanical damage, etc. also. For this reason, it is important to monitor the charging process. Electrical hazard: The device is designed to run on battery power (rechargeable battery). Meets your specifications. Never use the device with a type other than the recommended power supply: due to the risk of short circuit or electric shock. Stop using the light necklace if it falls into the water. Do not continue to use the product if it is damaged or dropped. Through a service center only improve to prevent risks. (Please note the warranty conditions) Failure / error: Does not work? Is the battery not charged? Connect the USB cable to the fluorescent lamp and charge the battery. Also check that the computer's USB port is working. Technical data: Battery: 1 x 3.7 V- 100 mA Waste treatment: Always place the waste from the packaging of the product in the waste container in accordance with the material of the product. The device must not be disposed of with household waste. This product is covered by Directive 2012/19 / EU of the European Parliament and of the Council on electrical and electronic equipment Dispose of your electronic equipment at your local collection point or waste disposal company. THE For waste disposal, please follow local waste disposal regulations. If in doubt a for waste disposal, please contact your local waste disposal company. Battery Disposal: Defective or worn out battery, battery pack or battery in accordance with Commission Directive 2002/66 / EC individual cells should be collected in an environmentally friendly manner and their waste treated. Adequacy: We declare that the product meets the essential requirements and complies with the following specifications and regulations: EN61000-6-3: 2007 + A1: 2011 EN61000-6-1: 2007 (IEC 61000-4-2: 2008 / IEC 61000-4-3: 2010) EN50581: 2012 2004/108 / EC of the European Parliament and of the Council European Parliament and Council 2011/65 / EU